Shopfox W1837 10″ 2 HP Open-Stand Hybrid Table Saw
This 10’ and 2HP hybrid table saw is simply amazing. With the Shop Fox W1837, you get the best of both worlds. The easy-to-transport weight and size of a high-end contractor saw, but with dust control and the full features of a cabinet saw.
Just like the Shop Fox professional cabinet saws, this hybrid also has a quick-change blade guard with anti-kickback pawls that can be positioned away from the workpiece. This saw will surely be the envy of any that see it in a shop or worksite.
This Hybrid Table Saw features cabinet-mounted trunnions and an enclosed steel upper-stand for maximum dust containment. Despite its hybrid design, cutting capacities stand toe-to-toe with the most expensive cabinet saws in the market.
The interchangeable riving knife offers protection for non-through cutting operations that require removal of the blade guard. Also features a serpentine belt and pulley system for smooth and quiet operation with better power transfer than a standard V-belt drive system. This saw is sure to be the envy at any shop or worksite.
- Is strong, hard wearing and durable
- Is very easy to use
- Comes with anti kickback pawls that can be positioned anywhere
- You can easily change blades
- Is very expensive
- Requires a lot of power
- Motor: 2 HP, 120V/240V, single-phase
- Pre Wired to 120V
- Amps: 15A at 120V, 7.5A at 240V
- Weight: 243 lbs
- Rip capacity: 30″ to right, 15″ to left
- Speed: 3450 RPM
- Maximum blade diameter: 10″
- Arbor: 5/8″
- Maximum Depth of Cut At 90 Degrees: 3-1/4″
- Maximum Depth of Cut At 45 Degrees: 2-1/4″
- Blade tilt: Left
- Enclosed cabinet bottom with 4″ dust port
- Precision-ground cast iron table
- Table measures: 40-1/4″ x 27″
- Lift-off Precision Fence with front/rear locking ability
- Quick‐Release Blade Guard Assembly
- Riving knife
- Robust Cabinet Mounted Trunnions
- Built-in foot operated mobility system
- T‐Slot Miter Gauge
- Easy‐Glide Fence System
- Quick‐Release Blade Guard Assembly
Interchangeable true riving knife
The interchangeable true riving knife offers protection for non-through cutting operations that require you to remove the blade guard.
Built-In Mobile Base
The W1837 features a handy built-in kickstand operated mobile base. With a simple push down on the foot levers the machine rises off it’s otherwise stable feet to become mobile so you can easily move it to your new desired location.
Enclosed cabinet bottom with 4-inch dust port. The enclosed cabinet bottom features a dust chute with a 4-inch port. Keep your work area free of dust and debris when connecting a dust collector with at least 400 CFM available.
The blade can tilt to the left from anywhere between 0 and 45-degrees. Great for cutting bevels, compound miters or chamfers. Easily adjust your cutting angle by loosening the blade tilt lock and turning the blade tilt handwheel to position the blade at the desired angle, then lock it in place for consistent repeat angled cuts.
Quick‐Release Blade Guard Assembly
The clear guard allows the operator to watch the blade cut the workpiece during operation while maintaining a barrier around the blade that prevents accidental contact and keeps flying wood chips contained. The spreader/riving knife is a metal plate that prevents the newly cut kerf in the workpiece from pinching the back side of the blade, and otherwise causing potential kickback.
The anti-kickback pawls allow the workpiece to travel in only one direction. If the workpiece moves backwards, such as during a kickback, the pawls will dig into the workpiece to slow or stop it. Includes a 10″ x 40-tooth carbide tipped blade, standard and dado table inserts, miter gauge, push stick, and arbor wrenches
What’s a “hybrid” table saw?
A hybrid table saw is a stationary table saw, built to look like a more expensive cabinet maker saw, with the motor inside, but with internals more like a less expensive “contractor saw”. So it’s a hybrid between a cabinet maker saw and what was traditionally known as a contractor saw.
Cabinet maker saws tend to be sturdy and heavy, typically with a 3 hp motor, requiring a 240 volt circuit. The trunnions and saw mechanism are mounted directly onto the cabinet base, whereas on a hybrid table saw they are usually just bolted to the bottom of the cast iron table.
What was traditionally a contractor saw is a saw with a cast iron table, a stand, or legs that can be detached, a tilt mechanism bolted to the bottom of the table, and an induction motor hanging out the back. The heavy motor is easy to remove, and with the motor off such a saw is fairly luggable by two people.
A “Hybrid” table saw is Essentially a contractor saw with a stand that is fully enclosed, and motor inside instead of on the back. This makes the saw more convenient in the workshop, but it also makes it harder to move.
But given that most old style contractor saws are stationary in a hobby workshop these days, this arrangement makes more sense. It doesn’t cost any more to make one of these saws than an old style contractor saw. As such, most manufacturers no longer make traditional contractor saw type saws, making hybrid table saws instead.
A downside of having the blade tilt raise and lower mechanism and motor hanging off the bottom of the table is that the cast iron table will sag slightly over time. Sagging cast iron sounds hard to believe, but, yes, it happens!
Trunnions bolted to the bottom of the table also makes it much more difficult to adjust the blade alignment (though, ideally that is already set correctly when you buy the saw)
Contractors these days use more portable “jobsite” saws (also referred to as benchtop table saws), As such, these jobsite saws are now often referred to as contractor saws.
Jobsite saws use smaller universal motors, which are much lighter, but also less durable and very loud. The motor is on the inside. These saws are less solid than cast iron contractor saws, but the increased portability more than makes up for it.
Just like standard cabinet saws, the Shopfox W1837 trunnions mount to the cabinet for superior performance. The robust cast iron trunnions absorb vibration, ensure proper blade-to-fence and miter slot alignment and make blade height and angle adjustments a breeze. There’s so much more listed above about this saw that you will love. So go get yours now before it’s too late.
- Walnut Hollow Creative Versa with Variable Temperature Control & 11 Changeable Tips - October 26, 2020
- Beavercraft DK1S Drawknife with Oak Handle in Leather Sheath - October 24, 2020
- Old Timer 24OT Splinter Carvin’ 6in Traditional Folding - October 23, 2020